可拆卸式橡膠止水帶300寬

橡膠止水帶是用來進行止水的;鋼邊橡膠止水帶在橡膠中間焊止水片外面近模板處焊定位片,對于鋼邊橡膠止水帶要求滿焊,定位片只要牢固就可以了,定位片距模板要有一到二公分的距離,這之間加塑料或者木質墊片。拆模后剔出,割掉螺桿后用微膨脹砂漿填平。還有種國內少見 就是用短一點的螺桿外加連接螺桿,拆模后可以很方便的拆下。
The rubber sealing strip is used for sealing; steel edged rubber water stop outside the middle rubber waterstop welding near the template at the welding positioning piece, the steel edged rubber water stop full welding requirements, as long as the firm positioning piece can, positioning distance template to one to two cm distance, plastic or wooden pads plus this. After stripping out, cut off after the mortar filled with micro expansion screw. There are kinds of domestic rare connection screw rod is a little shorter, after stripping can be easily disassembled.
橡膠止水帶是在混凝土澆注過程中部分或全部澆注埋進混凝土中。在澆埋混凝土以前先要使其在界面部位保持平展，接頭部分粘接緊固，再以適當的力充分澆搗，震蕩混凝土來定位止水帶，使其與混凝土良好的結合，以免影響止水效果。

可拆卸式橡膠止水帶300寬
The rubber water stop belt is partially or completely poured into the concrete during the concrete pouring process. Before pouring the concrete, it is necessary to keep it at the interface part. The joints are fastened and fastened. Then the concrete is fully poured and tamper with the appropriate force. The concrete is positioned by the shock concrete to make the water stop band well combined with the concrete so as not to affect the sealing effect.
橡膠止水帶施工注意事項在施工過程中，由于混凝土中有許多尖角的石和銳利的鋼筋，所以在澆搗和定位止水帶時，應注意澆搗的沖擊力，以免由于力量過大而刺破橡膠止水帶。如果發現有破裂現象應及時修補，否則在接縫變形和受水壓時橡膠止水帶抵抗外力的能力就會大幅度降低。固定止水帶時，只能在止水帶的允許部位上穿孔打洞，不得損壞本體的部分。在定位橡膠止水帶時，一定要使其在界面部

可拆卸式橡膠止水帶300寬
In the process of construction, because there are many sharp corners and sharp reinforcing bars in the concrete, the impact force should be paid attention to when pouring and locating the sealing belt, so as not to pierce the rubber water stop because of too much power. If the rupture is found to be repaired in time, the capacity of the rubber belt to resist external force will be greatly reduced when the joints are deformed and subjected to water pressure. When the sealing zone is fixed, the hole can only be perforated on the allowed part of the water stop belt, and the part of the body can not be damaged. When locating a rubber sealing belt, make sure that it is at the interface
位保持平展，更不能讓止水帶翻滾、扭結，如發現有扭結不展現象應及時進行調整在澆注固定止水帶時，應防止止水帶偏移，以免單側縮短，影響止水效果。在混凝土澆搗時還必須充分震蕩，以免止水帶和混凝土結合不良而影響止水效果。止水帶接頭必須粘接良好，如施工現場條件具備，可采用熱硫化連接的方法。不加任何處理的所謂“搭接”是不允許的。
The position is kept flat, and it can not even make the water stop roll and twist. If there is a kink and no appearance, it should be adjusted in time. When the fixed watertight belt is placed, the waterstop should be prevented from being offset, so as to avoid the shortening on one side and affect the sealing effect. When the concrete is poured, it must also be fully concussion, so as to avoid the bad combination of water and concrete, which will affect the effect of water stop. The joint of the water stop belt must be well bonded, such as the condition of the construction site, and the method of hot vulcanization can be used. The so-called "lap" without any treatment is not allowed.

河北瑞博橡塑制品有限公司是一家集橡膠支座，橡膠止水帶，伸縮縫等工程橡膠制品為主的專業生產企業。歡迎各界朋友蒞臨參觀指導，業務洽談。歡迎致電：13166570832