FD-60型伸縮縫安裝 |
![]() |
價格:1 元(人民幣) | 產地:衡水 |
最少起訂量:1米 | 發貨地:衡水 | |
上架時間:2017-10-10 14:05:58 | 瀏覽量:138 | |
河北瑞博橡塑制品有限公司
![]() |
||
經營模式:生產加工 | 公司類型:私營有限責任公司 | |
所屬行業:橡膠制品 | 主要客戶:全國 | |
![]() ![]() |
聯系人:王偉 (先生) | 手機:13166570832 |
電話: |
傳真: |
郵箱:3407742055@QQ.COM | 地址:河北省衡水市景縣留府工業區 |
FD-60型伸縮縫安裝 1、如要在先攤鋪路面后裝伸縮縫,為保證路面良好的平整度,應該先攤鋪路面,然后開槽安裝伸縮縫。攤鋪路面之前,必須首先清理預留間隙并嵌填泡沫板,再用砂袋或級配砂石袋填實槽口;靥顦烁咭钥刂茷r青不會污染預埋鋼筋為宜,目的在于防止攤鋪設備壓壞預埋鋼筋,便于路面連續攤鋪。 1, if it is necessary to spread the road before installing expansion joints, in order to ensure a good level of pavement, it should be paved pavement, and then slotted installation expansion joints. Before paving the road, must first clear the reserved space and filled with sand filled foam board, or graded sand gravel bag slot. In order to control the elevation of backfill will not pollute the asphalt and pre buried steel should be designed to prevent spreading equipment for crushing and pre buried steel, continuous pavement paving.2、橋面的切縫、清槽按預留的槽口寬度用切縫機對路面的油面層進行切縫。切縫時應注意保持路面切口完好,無啃邊現象。切縫后及時清除槽內瀝青混凝土及填料,鑿毛槽口內混凝土表面。這一系列工序非常重要,它將影響混凝土的澆筑質量。 2. The cutting seam and the cleaning groove of the bridge are slit with the cutting machine on the width of the reserved notch. Attention should be paid to maintaining good pavement incision and no undercut while cutting. After cutting, clean the asphalt concrete and packing in the slot, and then cut the concrete surface in the notch. This series of processes is very important, it will affect the quality of concrete pouring. 3、在安裝伸縮縫時,下縫前應認真檢查槽內預埋鋼筋,若發現裂縫或折斷,位置不當或間隙過大,必須采取補救措施。要保證沿縫方向每米范圍內至少有1根預埋鋼筋與毛勒伸縮縫的錨環牢固焊接。應該認真檢查XF型橋梁伸縮縫質量,若發現變形或兩鋼梁間距不一致時,應進行修整。必要時,還應根據安裝時的環境溫度調整毛勒伸縮縫的鋼梁間距。應將XF型橋梁伸縮裝置緩緩放入槽內,使縫中心線與實際預留縫中心線相重合,偏差不得超過10mm,同時使鋼邊梁內邊保持垂直。XF型橋梁伸縮縫就位后,應根據縱、橫坡和標高調整其鋼梁頂面比相鄰瀝青混凝土路面低1~2mm,不得超出路面標高。
FD-60型伸縮縫安裝
4、在焊接先點焊部分預埋鋼筋和錨環鋼筋,臨時固定其位置。經檢查符合質量要求后方可將錨環鋼筋與預埋鋼筋焊牢,之后,即可拆除XF型橋梁伸縮縫的裝配夾具。 4, in welding first spot welding part, pre embedded steel bar and anchor ring steel bar, temporary fixed position. After inspection to meet the quality requirements before the anchor ring reinforcement and embedded steel, welding, assembly fixture can be demolished XF type bridge expansion joint. 5、對于立模、澆混凝土立模應注意模板密封,切忌水泥漿漏入支撐箱,影響支承部件和控制系統的正常工作。澆筑混凝土之前,在錨環內應插入一定數量縱向鋼筋;在鋼邊梁水平肢上加鋪一層鋼筋網;在支撐箱底板上設置雙層防震鋼網。應采用低收縮、快硬、早強混凝土,其標號不得低于上部結構混凝土標號。特別注意錨板、錨環及橫梁支撐箱下面的混凝土密實。在混凝土養護期內,禁止一切車輛通行。 5, for formwork and concrete pouring formwork should pay attention to the template sealing, avoid cement slurry leak into the support box, affect the supporting parts and control system of normal work. Before pouring concrete, a certain amount of longitudinal reinforcement should be inserted into the anchor ring; a layer of reinforcing steel net is added to the horizontal edge of the steel edge beam; a double-layer shock proof steel net is arranged on the bottom plate of the support box. Low shrinkage, quick hardening and early strength concrete shall be adopted, and their grade shall not be lower than that of upper structure concrete. Pay special attention to the concrete density under the anchor plate, anchor ring and cross beam support box. During the maintenance period of the concrete, all vehicles are forbidden to pass. SGF120橋梁伸縮縫的產品特點如下: SGF120 bridge expansion joint products are as follows: 1、該橋梁伸縮縫采用擠出成型的Q345(ASTM A709Grade50)型鋼,強度高。型鋼為齒型結構,增加了伸縮量,提高了行車平穩,適用于高速公路及城市道路的橋梁伸縮縫,并能較好地適應橋梁的縱向位移。 1. The expansion joint of the bridge is made of extruded Q345 (ASTM, A709Grade50) steel with high strength. The section steel is a tooth type structure, which increases the expansion amount and improves the running stability. The utility model is suitable for the expansion joint of the highway and the urban road, and can well adapt to the longitudinal displacement of the bridge.
FD-60型伸縮縫安裝 2, the expansion of the bridge expansion joint is 0 ~ 120mm, between the expansion amount between 80mm and 160mm, to avoid the use of expansion joint expansion caused by the unstable running as the expansion device of 80mm, and increase the project cost and the amount of expansion joint expansion problem 160mm. 3、采用的錨固系統與GQF-MZLⅡ80相同,適用于各種梁端結構,其預留槽(包括鋪裝層)高度≥150mm。 3, the anchor system and GQF MZL II 80, applicable to all kinds of beam structure, the slot (including pavement) height greater than 150mm. 4、將W型氯丁橡膠伸縮密封條嵌入型鋼內,防水、防塵性能佳。 4, W type neoprene telescopic sealing strip embedded in the steel, waterproof and dustproof performance is good. FD-60型伸縮縫安裝
|
版權聲明:以上所展示的信息由會員自行提供,內容的真實性、準確性和合法性由發布會員負責。機電之家對此不承擔任何責任。 友情提醒:為規避購買風險,建議您在購買相關產品前務必確認供應商資質及產品質量。 |
機電之家網 - 機電行業權威網絡宣傳媒體
關于我們 | 聯系我們 | 廣告合作 | 付款方式 | 使用幫助 | 會員助手 | 免費鏈接Copyright 2025 jdzj.com All Rights Reserved??技術支持:機電之家 服務熱線:0571-87774297
網站經營許可證:浙B2-20080178